minghungmachinery@gmail.com   ▏ +86-18769900191 / +86-15589105786
Veneer Peeling
You are here: Home » Product Groups » Veneer Peeling

PRODUCT CATEGORY

Veneer Peeling

Reasonably organize the selection of veneer peeling lines. To reduce the deformation of thick veneer after drying, use
The toothed pressure gauge stabs teeth marks on the front of the veneer to eliminate the imbalance caused by the cracks on the back.
The reason is that the veneer wood core is sawed off and then rotated. Some wood segments cannot be straightened due to defects such as heart rot and cracking.
By reducing the diameter of the wood core, this part of the defect can be broken off, and it can be carried out on a special small rotary cutting machine.
Rotary cutting, the obtained veneer can be used as a large-format plywood core or made into a small-format plywood. also
The wood core can be re-spinned by a rotary cutter without a card shaft. Manually conveying and picking veneers is easy to damage, and it will affect the
The productivity of the rotary cutter. At present, the mechanical sorting and transportation method is widely used, which not only selects the veneer
It can also improve the output of the rotary cutting machine. The basic method is: the unusable veneer unscrewed from the rotary cutting machine
And the available veneer can be divided into two pipelines; or the rotation and rotation of the wood segment can be divided into two processes.
Divide the peeled veneer into two lines, one is available and the other is unavailable. not available
The plate passes through the valve, falls on the conveyor belt, and is transported to a centralized place for processing (such as breaking, making fiber, etc.)
Dimensional board or particle board raw material, can also be used as fuel). Useful veneers can be transported through the upper part of the valve
Go to the workbench behind the rotary cutting machine for finishing and cutting, and the broken veneer needs to be cut and shortened. continuous
The veneer tape is then shipped directly to cut or reel storage or conveyor belt storage. Wet veneer edge sealing especially
When peeling thin veneers, tapes should be attached to both ends of the veneer to prevent the veneer from being torn off in subsequent processing.
open, resulting in loss. Roll into rolls and store 1L before drying, so that the tape can be tightly glued to the
single board
Availability:
Quantity:
  • MH-VPM4A VPM8
  • MINGHUNG

veneer peeling 

veneer peelingwood peelinglog peeling

Reasonably organize the selection of veneer peeling lines. To reduce the deformation of thick veneer after drying, use

The toothed pressure gauge stabs teeth marks on the front of the veneer to eliminate the imbalance caused by the cracks on the back.

The reason is that the veneer wood core is sawed off and then rotated. Some wood segments cannot be straightened due to defects such as heart rot and cracking.

By reducing the diameter of the wood core, this part of the defect can be broken off, and it can be carried out on a special small rotary cutting machine.

Rotary cutting, the obtained veneer can be used as a large-format plywood core or made into a small-format plywood. also

The wood core can be re-spinned by a rotary cutter without a card shaft. Manually conveying and picking veneers is easy to damage, and it will affect the

The productivity of the rotary cutter. At present, the mechanical sorting and transportation method is widely used, which not only selects the veneer

It can also improve the output of the rotary cutting machine. The basic method is: the unusable veneer unscrewed from the rotary cutting machine

And the available veneer can be divided into two pipelines; or the rotation and rotation of the wood segment can be divided into two processes.

Divide the peeled veneer into two lines, one is available and the other is unavailable. not available

The plate passes through the valve, falls on the conveyor belt, and is transported to a centralized place for processing (such as breaking, making fiber, etc.)

Dimensional board or particle board raw material, can also be used as fuel). Useful veneers can be transported through the upper part of the valve

Go to the workbench behind the rotary cutting machine for finishing and cutting, and the broken veneer needs to be cut and shortened. continuous

The veneer tape is then shipped directly to cut or reel storage or conveyor belt storage. Wet veneer edge sealing especially

When peeling thin veneers, tapes should be attached to both ends of the veneer to prevent the veneer from being torn off in subsequent processing.

open, resulting in loss. Roll into rolls and store 1L before drying, so that the tape can be tightly glued to the

single board

MINGHUNG Veneer peeling latheminghung veneer latheMINGHUNG veneer peeling line

The veneer peeling requires that the surface of the veneer be flat without chicken feet and no back cracks. Uniform thickness of veneer

minghung mchine details

More about veneer peeling contact us:

whatsapp: +8618769900191   +8615589105786   +8615805493072

website: www.plywoodmachineline.com 

email: minghungmachinery@gmail.com 

Previous: 
Next: 
Shandong MINGHUNG Wood Machinery Co.,Ltd is one famous manufacturer of plywood machine in China, located in Linyi city. 

Home

CONTACT US

 +86-18769900191 /  +86-15589105786 
 +86-18769900191 / +86-15589105786
 
minghungmachinery@gmail.com
  Fangcheng Town,Lanshan District,Linyi City,Shandong Province,China
Copyright © 2010 SHANDONG MINGHUNG WOOD MACHINERY CO.,LTD