Beech veneer dryer
The advantages of beech: 1. Beech has good quality and beautiful wood grain. The appearance of beech wood is quite eye-catching, the wood color is soft, the color is rich, and the texture of the visual inspection is quite uniform. It can be used to make furniture, and it can also be used to make plywood.
2. Beech wood is hard and has strong resistance to punching. Because the production cycle of the product beech is long enough, the beech itself has high density, good strength and is very hard. Beech wood used to produce veneer needs to be cooked after cooking, and beech veneer is produced with veneer peeling machine.
Disadvantages of beech veneer: 1. Cracking. Especially in the production process of veneer dryer, because the hardness of wood is too hard, if the veneer is used in a tumble dryer, it is easy to break under the pressure of the drum of the dryer, so a mesh bag dryer is used for hardness. After drying, beech veneer is very Flat, because the mesh bag has no pressure, effectively preventing the beech veneer from breaking.
2. Beech veneer is prone to chromatic aberration, because the production cycle of beech is long, and if the procurement of raw materials is not uniform, it will cause the beech veneer after production to have a large color difference.
According to your conditions and needs, like the production capacity, the thickness of wood veneer, your workshop room, your budget, your future plans..., to choose one good and suitable machine.
Just tell us your requires and conditions, we will offer you the professional advice and offer the most suitable veneer dryer machine to you.
MINGHUNG veneer dryer is a dryer specially developed for traditional dryers with high energy consumption, low drying efficiency, uneven drying of veneers and high mechanical failure rate. This model has high energy consumption and high heat conversion rate. , The drying veneer is flat, the failure rate is low, and the pain point of the traditional dryer is solved. This model has the following advantages:
1. High output at low temperature, ensuring the flexibility and flexibility of the veneer, fast speed and large output. According to the needs of different users and different materials, the output of the equipment can reach 3-4 cubic meters per hour.
2. In order to achieve the flatness of the drum, we optimize the density of the internal machine structure to reduce the pressure, completely solve the problem of the flatness of the veneer, and avoid the problem of reducing the size of the veneer caused by excessive pressure. Smaller shrinkage than all dryers on the market, no loss of veneer,
3. High degree of automation, automatic feeding and labor saving, automatic dehumidification, low cost of consumables, high efficiency and energy saving, low power consumption, the equipment adopts all-aluminum fin heating device, large heat exchange area, fast heating, large circulating air volume, and many cycles. High thermal efficiency, drying equipment saves more than 40% energy. All cooling fins adopt forced circulation system to enhance fluid flow rate, improve heat exchange efficiency, and effectively reduce heat loss. At the same time, the problem of excessive wind resistance caused by high coil density is effectively solved, and the heat transfer process is improved by 1.5 times compared with the traditional dryer.
4. To prevent the phenomenon of returning moisture, the length of the cold air area is longer than that of the traditional dryer, the cooling effect of the veneer is better, and the drying is even. The stripped veneer undergoes multi-stage heat exchange and dehumidification. After drying for about 1.5 hours, the moisture content is low and uniform, which can meet the production needs of veneer and plywood.
5. The whole machine is insulated to prevent heat loss and reduce the impact on the environment.
6. The negative pressure fan design is adopted, which improves the air volume and wind pressure efficiency by 2-3 times compared with the traditional positive pressure fan, effectively solving the problem of low conversion efficiency of the fan motor power large air volume transmission
7. The dryer is forced to dehydrate due to interference. During the dehydration process, the veneer will have problems of poor flatness and finish due to excessive shrinkage. We increase the density and reduce the pressure to effectively solve the problem of the flatness of the veneer, while avoiding excessive pressure. Mass reduction problem.
SHANDONG MINGHUNG WOOD MACHINERY CO.,LTD
The veneer (plywood) dryer can be divided into three heating forms: hot air heating, steam heating, and heat transfer oil heating according to different heating forms. According to different fuels, it can be divided into fuel oil, gas, coal, firewood, and electricity. The equipment can be divided into manual loading and automatic loading. The veneer enters the dryer, and according to the set value, the temperature and humidity in the dryer are automatically controlled, so that the drying material can be leveled and the moisture can be controlled uniformly. The equipment can determine the size of the equipment according to the user's output, and it can be divided into automatic board and manual board. This equipment has large output, high degree of automation, low cost of use, uniform drying, and good effect. Through drying, it can avoid mildew and blue change of plates in high temperature and high humidity environment (such as eucalyptus wood, rubber wood, poplar, camphor It is ideal in the field of veneer processing, flame retardant veneer production, plywood production, flame retardant plywood production, and dyed veneer (board) production. Veneer drying equipment.
product description
Product advantages: This equipment has a high degree of automation, low operating cost, small footprint, and can be operated 24 hours a day, saving labor, and the annual labor cost saving can reach 150,000 US dollars.
Obvious features:
1. High degree of automation, automatic loading, labor saving, automatic heating, dehumidification, high drying intensity, long drying time, high moisture saturation, and energy saving.
2. Dry evenly. The peeled veneer undergoes heat exchange and moisture removal in multiple sections, and after drying for about 1.5 hours, the moisture content is low and uniform, which can meet the production needs of veneer and plywood.
3. The output is large. According to the needs of different users and different materials, the output of the equipment can reach 1---5 cubic meters/H.
4. The equipment adopts fin-type heating device, which has large heat exchange area, fast temperature increase, large circulating air volume, many cycles, high heat exchange efficiency, high exhaust water saturation, energy saving, and low use cost, which is better than roller type veneer. The drying equipment saves energy by more than 40% (the roller adopts the air spray method, the contact time between the hot air and the plate is short, and the heat exchange efficiency is low).
5. A piece of equipment investment can be used for more than ten years, super cost-effective
6. The failure rate is low, the network belt is worn, and the network is disconnected, and the failure rate of the pallet is low.
7. The equipment adopts vertical plate loading and drying. The operation time of the plate skin in the equipment is long, which can reach 1-2 hours. The temperature can be controlled according to the section. 13----15min, the folding type veneer dryer has large output, low energy consumption and low drying cost.
